Showing results: 1366 - 1380 of 2628 items found.
-
Circuit Check, Inc.
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Q1 Test, Inc.
In-circuit-testing (ICT) is usually used on mature products, especially in subcontract manufacturing. It uses a bed-of-nails test fixture to connect with multiple test points on the PCB’s bottom side. With sufficient access points, ICT can transmit test signals into and out of PCBs at high speed to apply evaluation of components and circuits.
-
3604 -
Peaceful Thriving Enterprise Co Ltd
1. Checks voltage on 6, 12 and 24V systems.2. 12-feet flexible rubber wire with spring relief.3. Tough plastics handle lights up if circuit is good.4. 4mm connection for banana plugs.5. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
40-220A-601 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
LDC-5/D -
Doble Engineering
For LDS-6. Double impulse calibrator. For external calibration of the standard PD measuring circuit according to IEC 60270 (single pulses). PD measurements on long cables and in accordance with standards requiring the verification of the double pulse behavior of the employed PD measuring system. Produces these standardized time parameters according to the IEC 855-3.
-
LBW -
Simplex Inc
The LBW-Series Load Banks are completely self-contained, freestanding units which include all resistive load elements, load control devices, load element branch circuit fuse protection, main load bus and terminals, water cooled system, control power supply, unit controller and malfunction detection system.
-
FilmTek 4000 -
Scientific Computing International
Fully-automated wafer metrology optimized for photonic integrated circuit manufacturing. Delivers unmatched measurement accuracy, with a 100x performance advantage over the best non-contact method and 10x that of the best prism coupler contact systems. Designed to enable optical component manufacturers to increase functional yield of their products, reliably and at lower cost.
-
Premier Electrosystems
Premier Electrosystems deals in a wide range of voltage and current sensing devices. A Current/ Voltage sensor is a device that detects electric current/ voltage in a circuit and generates proportional signal. The generated signal can be then used to display the measured current in an ammeter, or can be stored for further analysis in a data acquisition system, or can be used for the purpose of control.
-
Vidac Solutions
This system is a modern replacement for an obsolete product tester. This tester Hipots the lamp under test, checks for proper operation at the required voltage and also detects short circuit operation and the 5KV ignitor pulse signal. This tester allows for quick calibration to permit traceable/repeatable results and store the test results for product tracking.
-
MRC ltd.
Tension & compression capability .* 5000 g, wide capacity, highresolution, high accuracy, highrepeatability.* 3 kind display unit, g/oz/Newton.* Separate sensor.* Peak hold ( Max. load ) measurement.* Positive or reverse display direction.* Hand held & stand mounting.* Microprocessor circuit & exclusiveload cell transducer.
-
LM Series -
Koyo Electronics Industries co., ltd
Models in LM-2100 series equipped with LCR meter are designed to measure inductance and dissipation factor of the coil to which DC current is superimposed. Special circuit is built in to protect the LCR meter from surge voltage. Applied current can be step by step in the remote mode. Voltage application is impossible with the safety cover open.
-
40-220A-701 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
40-220A-501 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
40-220A-201 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
40-220A-401 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.